Cabinet Installation in Meridian, Idaho
Hang, scribe, and level. Builder walls in new plats are rarely plumb. We leave a counter line.
Free estimate.
- Free estimates
- Treasure Valley
- Local crew
- One number
This job covers
- Scribe to out-of-plumb drywall
- Shim bases on a slab
- Ledger hang for wall boxes
- Island set on a level line
Cabinet Installation in Meridian, Idaho
Meridian Quality Cabinets provides cabinet installation in Meridian as a hang, scribe, and lag on walls that are rarely plumb. Production drywall is not a furniture shop. We shim, scribe, and lag so doors still line up.
Use (208) 759-1616 to say whether the boxes exist or we are building them. Hang day follows a wall check.
Cabinet Installation Options for Meridian Properties
Scribe to out-of-plumb drywall
A 1/2 inch wander over 8 feet is common in south Meridian plats. We scribe the end panel with a compass and a belt sander. Fillers pick up the last gap. Caulk is not a scribe. If the wall bows, the door reveal tells on us unless we cut the panel.
Shim bases on a slab
Garage conversions and some first floors sit on a slab that is not level. We find the high point, snap a line, and shim every base to it. The toe-kick skin hides the shims. A peninsula that is 1/4 inch out will crack a stone top.
Ledger hang for wall boxes
Uppers go on a ledger or a steel rail lagged into studs, not into drywall anchors. We find studs, not guess. A 30 inch upper full of dishes is heavy. Two people lift. A laser sets the bottom line so the doors meet the hood.
Island set on a level line
An island is four finished sides and no wall to hide a mistake. We assemble on a flat line, lag into the floor with L-brackets where the plan allows, and check diagonals. Seating overhangs get blocking. Electrical is the electrician's hole, not ours.
How We Handle Cabinet Installation in Meridian
- Check the room is empty, dry, and has power. Mark studs and the high point of the floor.
- Dry-fit the corner boxes and the sink base. Recut fillers in the driveway if needed.
- Hang uppers on a ledger. Confirm the line with a laser before the second box.
- Set bases, clamp the runs, and lag. Shim until the counter line is dead level.
- Install doors, drawers, and hardware. Adjust six-way hinges until reveals even out.
- Scribe end panels and toe-kicks. You walk the room before we pack.
Materials and Methods
Install is lags, shims, a scribe saw, a laser, and a 4-foot level. We use construction adhesive where a box meets a wall that will never come off. Toe-kick skin is 1/4 inch plywood or a matching vinyl wrap, scribed to the floor.
Set is a laser, a ledger, and shims. Screw to studs, not only to drywall. 3/4-inch plywood boxes hang truer than particleboard. Soft-close hinges and full-extension slides get a final adjust. ANSI/AWI 0641 tolerances on custom casework. Scribe the filler. Toe-kick last. We do not hang wall boxes on a single toggle. A 600-pound wall-cabinet load is the KCMA structural idea, not a guess.
Fillers are 3/4 inch, ripped to the gap. Crown is coped at inside corners. Light rail is scribed to the door bottoms. A fridge panel gets a 3 inch filler and a 1/4 inch reveal so the door clears.
We do not set stone. We do not hook up a dishwasher. We leave a square, level run and a gap where the appliance belongs. If a box arrived racked from another seller, it stays on the floor until you decide.
What Cabinet Installation Cost in Meridian
HomeAdvisor and Angi put professional cabinet installation between about $1,935 and $10,763, with an average near $6,188 for a kitchen. Angi also notes labor from $50 to $250 per hour, or $100 to $300 per linear foot depending how the shop bids. Fixr puts labor near 30 to 50 percent of a kitchen cabinet job, often $50 to $200 per linear foot.
The hang is cheaper when the walls are plumb and the boxes are square. Stairs, a second-story carry, and a 1 inch out-of-level slab add time. We quote the hang we see, not a national average. Call (208) 759-1616 .
Hanging on Ten Mile fill vs Eagle custom walls
A hang is only as good as the walls and the boxes. We find studs. We find the high point of the floor. We dry-fit corners. South Meridian slabs on fill settle. Bases shim to a laser, not to the old toe-kick line, or the new stone will crack. Uppers go on a ledger lagged into studs. A racked RTA case from another seller stays on the floor. We do not lag a twisted box and hope caulk hides it.
Eagle custom walls with tall plates, trays nearby, and inset reveals take more scribe time. Production overlays on an 8-foot plate hang faster when the boxes are square. Second-story carries, a garage far from the kitchen, and a 1 inch out-of-level slab are the three hang multipliers. We say them on the wall check, not on invoice day. Two people lift uppers. A fridge panel gets a reveal so the door clears.
Crown is coped. Light rail is scribed. We do not set stone, hook a dishwasher, or hide a bad slab with caulk. The counter line is a laser. HOA rules rarely touch a hang day. Parking on a tight cul-de-sac in a 2000s plat does. Say if the side yard is vinyl and narrow so we plan the carry of a 96 inch pantry.
Laundry and mudroom boxes on the same trip need the machines out of the way and the garage door clear. We can hang a kitchen and a drop zone in one schedule when the shop labels every case. Ask for that plan early.
Call (208) 759-1616 with whether the boxes are on site, the town, and photos of the walls. We bid hang time after we see how far the walls wander.
Questions
How do I get a cabinet installation estimate in Meridian?
Say if the boxes are already on site or if we are building them. Name the town and the room. A photo of the walls and the stacked cases helps. We bid hang time after we see how far the walls wander.
Can you hang boxes I bought elsewhere?
Sometimes. We hang plywood cases that are square. Particleboard RTA that arrived damaged is a different conversation. If a box is racked, we tell you before we lag it to a stud. We do not warranty someone else's joinery. Name the town and the job when you call.
How long does a hang take?
A small bath vanity is hours. A full kitchen is often one to three days after the room is empty. Crown, light rail, and a fridge panel add time. Counter templating waits until the run is set and level. Ledger hang for wall boxes Uppers go on a ledger or a steel rail lagged into studs, not into drywall anchors.
What does cabinet installation cost by itself?
Angi and HomeAdvisor publish kitchen install averages near $6,188, with a common band of about $1,935 to $10,763. Labor-only is often quoted per linear foot or per box. Access, stairs, and out-of-plumb walls move it. We bid the hang we see.
Does fill settlement in south Meridian change a cabinet hang?
Yes. Bases follow a laser level, not the dip in the slab. Large shims are normal on Ten Mile-belt houses. A huge shim pack can be a floor conversation. We will not set stone on a run that follows a wavy slab.
Can you hang a kitchen and a mudroom on the same visit?
Often yes if the shop labeled both runs and the garage path is clear. Mudroom benches on a slab need levelers. Kitchen uppers need a ledger. We stage the heavier kitchen boxes first when the truck is tight. Shim bases on a slab Garage conversions and some first floors sit on a slab that is not level.
Ready for a cabinet estimate in Meridian?
Kitchens, vanities, built-ins. Free estimate, no obligation.