Cabinet Installation in Meridian, Idaho

Meridian Quality Cabinets provides cabinet installation in Meridian, Idaho. Production drywall is not a furniture shop. We shim, scribe, and lag so doors still line up.

Use (208) 759-1616 to say whether the boxes exist or we are building them. Hang day follows a wall check.

Cabinet Installation Options for Meridian Properties

Scribe to out-of-plumb drywall

A 1/2 inch wander over 8 feet is common in south Meridian plats. We scribe the end panel with a compass and a belt sander. Fillers pick up the last gap. Caulk is not a scribe. If the wall bows, the door reveal tells on us unless we cut the panel.

Shim bases on a slab

Garage conversions and some first floors sit on a slab that is not level. We find the high point, snap a line, and shim every base to it. The toe-kick skin hides the shims. A peninsula that is 1/4 inch out will crack a stone top.

Ledger hang for wall boxes

Uppers go on a ledger or a steel rail lagged into studs, not into drywall anchors. We find studs, not guess. A 30 inch upper full of dishes is heavy. Two people lift. A laser sets the bottom line so the doors meet the hood.

Island set on a level line

An island is four finished sides and no wall to hide a mistake. We assemble on a flat line, lag into the floor with L-brackets where the plan allows, and check diagonals. Seating overhangs get blocking. Electrical is the electrician's hole, not ours.

How We Handle Cabinet Installation in Meridian

1. Check the room is empty, dry, and has power. Mark studs and the high point of the floor.
2. Dry-fit the corner boxes and the sink base. Recut fillers in the driveway if needed.
3. Hang uppers on a ledger. Confirm the line with a laser before the second box.
4. Set bases, clamp the runs, and lag. Shim until the counter line is dead level.
5. Install doors, drawers, and hardware. Adjust six-way hinges until reveals even out.
6. Scribe end panels and toe-kicks. You walk the room before we pack.

Materials and Methods

Install is lags, shims, a scribe saw, a laser, and a 4-foot level. We use construction adhesive where a box meets a wall that will never come off. Toe-kick skin is 1/4 inch plywood or a matching vinyl wrap, scribed to the floor.

Fillers are 3/4 inch, ripped to the gap. Crown is coped at inside corners. Light rail is scribed to the door bottoms. A fridge panel gets a 3 inch filler and a 1/4 inch reveal so the door clears.

We do not set stone. We do not hook up a dishwasher. We leave a square, level run and a gap where the appliance belongs. If a box arrived racked from another seller, it stays on the floor until you decide.

What Cabinet Installation Cost in Meridian

HomeAdvisor and Angi put professional cabinet installation between about $1,935 and $10,763, with an average near $6,188 for a kitchen. Angi also notes labor from $50 to $250 per hour, or $100 to $300 per linear foot depending how the shop bids. Fixr puts labor near 30 to 50 percent of a kitchen cabinet job, often $50 to $200 per linear foot.

The hang is cheaper when the walls are plumb and the boxes are square. Stairs, a second-story carry, and a 1 inch out-of-level slab add time. We quote the hang we see, not a national average. Call (208) 759-1616 .

A hang is only as good as the walls and the boxes. We find studs. We find the high point of the floor. We dry-fit corners. A racked RTA case from another seller stays on the floor. Crown is coped. Light rail is scribed. A fridge panel gets a reveal so the door clears. We do not set stone, hook a dishwasher, or hide a 1 inch out-of-level slab with caulk. The counter line is a laser, not a guess from the far wall.

Second-story carries, a garage far from the kitchen, and a 1 inch out-of-level slab are the three hang multipliers. We say them on the wall check, not on invoice day. Two people lift uppers. A laser sets the bottom line. Fillers are ripped to the gap, not caulked to hide 3/4 inch. If you bought RTA elsewhere, we open a box and check square before anything is lagged. Racked cases stay on the floor.

Cabinet Installation Questions

How do I get a cabinet installation estimate in Meridian?

Say if the boxes are already on site or if we are building them. Name the town and the room. A photo of the walls and the stacked cases helps. We bid hang time after we see how far the walls wander.

Can you hang boxes I bought elsewhere?

Sometimes. We hang plywood cases that are square. Particleboard RTA that arrived damaged is a different conversation. If a box is racked, we tell you before we lag it to a stud. We do not warranty someone else's joinery.

How long does a hang take?

A small bath vanity is hours. A full kitchen is often one to three days after the room is empty. Crown, light rail, and a fridge panel add time. Counter templating waits until the run is set and level.

What does cabinet installation cost by itself?

Angi and HomeAdvisor publish kitchen install averages near $6,188, with a common band of about $1,935 to $10,763. Labor-only is often quoted per linear foot or per box. Access, stairs, and out-of-plumb walls move it. We bid the hang we see.